Houdini Main Changelogs
 |
4.9.583 | Adjusting the inset of a PolyExtrude SOP on an open polygon will now produce sensible results for the end points of the polygon. |
金. 1月 4, 2002 |
|
4.9.583 | Adjusting the inset of a PolyExtrude SOP on an open polygon will now produce sensible results for the end points of the polygon. |
金. 1月 4, 2002 |
|
4.9.583 | mplay is no longer started by hserver. This eliminates a lot of bugs with the user environment of the mplay which was started by hserver. mplay now uses a file lock which can be found in $HOME/houdini$VER/.mplay_lock. |
金. 1月 4, 2002 |
|
4.9.583 | mplay is no longer started by hserver. This eliminates a lot of bugs with the user environment of the mplay which was started by hserver. mplay now uses a file lock which can be found in $HOME/houdini$VER/.mplay_lock. |
金. 1月 4, 2002 |
|
4.9.583 | mplay is no longer started by hserver. This eliminates a lot of bugs with the user environment of the mplay which was started by hserver. mplay now uses a file lock which can be found in $HOME/houdini$VER/.mplay_lock. |
金. 1月 4, 2002 |
|
4.9.583 | mplay is no longer started by hserver. This eliminates a lot of bugs with the user environment of the mplay which was started by hserver. mplay now uses a file lock which can be found in $HOME/houdini$VER/.mplay_lock. |
金. 1月 4, 2002 |
|
4.9.583 | mplay is no longer started by hserver. This eliminates a lot of bugs with the user environment of the mplay which was started by hserver. mplay now uses a file lock which can be found in $HOME/houdini$VER/.mplay_lock. |
金. 1月 4, 2002 |
|
4.9.583 | Extrude should properly offset open polygons and no longer rarely not offset a point. |
金. 1月 4, 2002 |
|
4.9.583 | Extrude should properly offset open polygons and no longer rarely not offset a point. |
金. 1月 4, 2002 |
|
4.9.583 | Extrude should properly offset open polygons and no longer rarely not offset a point. |
金. 1月 4, 2002 |
|
4.9.583 | Extrude should properly offset open polygons and no longer rarely not offset a point. |
金. 1月 4, 2002 |
|
4.9.583 | Extrude should properly offset open polygons and no longer rarely not offset a point. |
金. 1月 4, 2002 |
|
4.9.583 | The Extrude SOP now uses a different (and more correct) tolerance computation when clamping. This may generate slightly different results with some files. There is no workaround. |
金. 1月 4, 2002 |
|
4.9.583 | The Extrude SOP now uses a different (and more correct) tolerance computation when clamping. This may generate slightly different results with some files. There is no workaround. |
金. 1月 4, 2002 |
|
4.9.583 | The Extrude SOP now uses a different (and more correct) tolerance computation when clamping. This may generate slightly different results with some files. There is no workaround. |
金. 1月 4, 2002 |
|
4.9.583 | The Extrude SOP now uses a different (and more correct) tolerance computation when clamping. This may generate slightly different results with some files. There is no workaround. |
金. 1月 4, 2002 |
|
4.9.583 | The Extrude SOP now uses a different (and more correct) tolerance computation when clamping. This may generate slightly different results with some files. There is no workaround. |
金. 1月 4, 2002 |
|
4.9.583 | If front and back faces are both turned off in the Extrude SOP, it no longer leaves ghost points. This will change the point counts in succeeding operations. There is no workaround to this. |
金. 1月 4, 2002 |
|
4.9.583 | If front and back faces are both turned off in the Extrude SOP, it no longer leaves ghost points. This will change the point counts in succeeding operations. There is no workaround to this. |
金. 1月 4, 2002 |
|
4.9.583 | If front and back faces are both turned off in the Extrude SOP, it no longer leaves ghost points. This will change the point counts in succeeding operations. There is no workaround to this. |
金. 1月 4, 2002 |
|
4.9.583 | If front and back faces are both turned off in the Extrude SOP, it no longer leaves ghost points. This will change the point counts in succeeding operations. There is no workaround to this. |
金. 1月 4, 2002 |
|
4.9.583 | If front and back faces are both turned off in the Extrude SOP, it no longer leaves ghost points. This will change the point counts in succeeding operations. There is no workaround to this. |
金. 1月 4, 2002 |
|
4.9.583 | The Extrude SOP no longer leaves ghost points when you specify no output for the front and back faces. |
金. 1月 4, 2002 |
|
4.9.583 | The Extrude SOP no longer leaves ghost points when you specify no output for the front and back faces. |
金. 1月 4, 2002 |
|
4.9.583 | The Extrude SOP no longer leaves ghost points when you specify no output for the front and back faces. |
金. 1月 4, 2002 |